Добрый день.
Пытался прошить принтер полученной на данном ресурсе прошивкой. Однако, как говорят ученые, что-то пошло не так. Теперь принтер запускается только, если ему через консоль подкинуть загрузчик и прыгать на адрес 40d80000. Прошивки ни оригинальную ни фикс не жрет. Типа имидж нот валид. Подскажите как исправить ситуацию? Спасибо.
В терминале вон чо
START-UP MODE : Monitor Program
Boot into pROBE+ like stand-alone mode
[Type 'help' to see command info.]
Version : Ver.0.30 (SANDPIPER) 2010-08-15
----------------------------------------------------------------
Do you want to download from external port?[N] : nn
pROBE+>
----------------------------------------------------------------
Do you want to download from external port?[N] : yy
Enter Start Address[0x40D80000] : 0x4400dd8800000000
Ready to download from Parallel/Usb/Serial (0x40D80000)
-------------------------
Samsung OTG, 2006
Link ID : [4F54240A]
-------------------------
Drv "design ware core" USB download<FS><HS><HS><EPB_RX 0x00000200>
Special Image is downloading(font, etc)...
-> Address is 0x40D80000
[[2745208 Bytes received]] - Complete Downloading
----------------------------------------------------------------
Do you want to download from external port?[N] : nn
pROBE+> ggoo 4400dd8800000000
Executing the code at 0x40D80000
NEW MAC
Begin MAA_Test Approval
NEW MAC
gIsIPv4PacketAccepted : 00000001
gIsIPv6PacketAccepted : 00000001
HTTP_WriteTotalPageCount uwOpcode[664]
HTTP_WriteTotalPageCount uwOpcode[664]
[PJL]Write Rom Process!!(Count=7340056)
==>> CJI_IF_SetFWUpdateState : code[00000001], arg1[00000087], arg2[00000000]
==>> CJI_IF_SetFWUpdateState : code[00000001], arg1[00000087], arg2[00000000]..
...........................................................
[PJL:FWUpgrade] 0x42000000 out 0x438FF140(7340056) ~ 0x43FFF158
[PJL:FWUpgrade] 0x24494D47 , ? S<
All Preparation is Done...
Now JUMP to Flash Write Procedure.!!!!!!!!
Flash Data Download Address : 0x42000000
===============================
Start flash_writer
===============================
verify_Image : 0x42000000
i_header->pul_start_addr : 0x00000000
i_header->ul_count : 0x00700000
model : 0x0300002F
flash type : 0x00010001
image type : 0x00000000
temp_buf : $IMG
SIG : $IMG
FlashCheckSum
{
check sum start address : 42000018, count : 00700000
check sum : 0000A5A5
} /* Checksum End
Source Checksum is valid
ul_rom_size[0x42700018]
Found new kernel(0x424F0018)!!!!
ZIP Dest : 0x40D80000
[[[FFFFFFF8]]], [[[000F69A8]]]
----------- Display Dcache Status ------------
Control register = 0x000510FA
Icahe : ON
Dcahe : OFF
MMU : OFF
Download Image from PC
{
Ready to download from Parallel/Usb/Serial (0x42000000)
-------------------------
Samsung OTG, 2006
Link ID : [4F54240A]
-------------------------
Drv "design ware core" USB download<HS><HS><EPB_RX 0x00000200>
Image includes PJL(0000001B) -> Waste 48 bytes
[[7340104 Bytes received]] - Complete Downloading
} /* Download End */
verify_Image : 0x42000000
i_header->pul_start_addr : 0x00000000
i_header->ul_count : 0x00700000
model : 0x0300002F
flash type : 0x00010001
image type : 0x00000000
temp_buf : $IMG
SIG : $IMG
FlashCheckSum
{
check sum start address : 42000018, count : 00700000
check sum : 0000A5A5
} /* Checksum End
Source Checksum is valid
ul_rom_size[0x42700018]
Found new kernel(0x424F0018)!!!!
ZIP Dest : 0x40D80000
[[[FFFFFFF8]]], [[[000F69A8]]]
Downloaded Image is not Valid
Reset Target and Run Flash Writing Program Again
