firmware source address : 0x41800000
firmware address to be written : 0x22222021
firmware size : 0x01111111
main : 0x22220022
sub : 0x11111111
image : 0x02602212
image reserved : 0x10011091
Can not find sig
[ POWER ON Booting... ]
Press any key to execute Monitor Program within 1 sec...
Loading Kernel...
New kernel was found...
checksum is valid
Run Kernel..
FW Upgrade JUMP : 408A7D40
RootWriteMonitorProgram : 400220D8
------------------------------------------------------------------------------
BackUp Debugging Message
------------------------------------------------------------------------------
Task Name: PJLT , Exception Type: Assert
------------------------------------------------------------------------------
Assertion failed:
file ..\..\..\..\Platform\App\MM\MM_Lib.c, line 2094
------------------------------------------------------------------------------
Call Stack
------------------------------------------------------------------------------
404FC5FC
404FEBE8
404F0968
404FEB28
4015EA7C
40104E6C
4015D48C
FFFFFFFF
FFFFFFFF
FFFFFFFF
FFFFFFFF
FFFFFFFF
FFFFFFFF
FFFFFFFF
FFFFFFFF
FFFFFFFF
FFFFFFFF
FFFFFFFF
FFFFFFFF
FFFFFFFF
FFFFFFFF
FFFFFFFF
FFFFFFFF
FFFFFFFF
FFFFFFFF
FFFFFFFF
FFFFFFFF
FFFFFFFF
FFFFFFFF
FFFFFFFF
FFFFFFFF
FFFFFFFF
------------------------------------------------------------------------------
ramsize= 41125FFF, gsbsize = 40E56134, FreeMemPtr = 40E55478, FreeMemStart = 40E55478
BOOT Debug is always Enabled!!
----------- ARM Control Coprocessor ------------
Control register = 0x 510ff
MMU : ON
Icahe : ON
Dcahe : ON
----------------------------------------------
Installed Memory = 32MB
<<< Reelase Mode >>>
<<<LogMsg_PrintOff>>>
<<<LogMsg_PrintOff>>>
<<<LogMsg_EngPrintOff>>>
Model Code : ML2165W
Main Kernel F/W Version : V3.00.01.15
Main Kernel F/W Date : MAY-07-2013
DRAM:>
<<<HAL_InitWDT>>> WatchDog Initialized !!!
Check PowerOn Mode PBA Port 0 ---- ( GPIO_Ctrl - 0xffffffff GPIO_Dir - 0xfffffe2a GPIO_In - 0x1f7fa )
Check PowerOn Mode PBA Port 1 ---- ( GPIO2_Ctrl - 0x7f3f GPIO2_Dir - 0xffff88c3 GPIO2_In - 0xfe0f )
################### Normal Mode Start##########################
[SPI_SFR_CTRL0 = 0x34000000]
[SPI_SFR_SCKCYC = 0x00030003]
USBTrdTim : Bus Clock [100000000], TrdTim[3]
USBTrdTim : Bus Clock [100000000], TrdTim[3]
=====Initializing MAC Driver =====
======NICCON Init Finish!!=========
MT1900 Task Mode is 1
WLAN_BCM_P2P_Initialize 158
=========================================
Check remained memory in region #0 (0x1126000)
rnid : 0x0
Remained RN#0 region : 0x15c000 - 1425408
=========================================DISCONNECTED -> ADDRESSING
ADDRESSING -> CONNECTED
======WSD Init Finish!!=========
после заливки fix прошивки пищать перестал. но остались пара вопросов, что ему не нравиться в этих ошибках? flash выпаивал и проверял. она без ошибок.
Check remained memory in region #0 (0x1126000)
Assertion failed: file ..\..\..\..\Platform\App\MM\MM_Lib.c, line 2094
