Общение > Помогите!
Помогите Прошивка Samsung ML-2580N
Рустам Умаркулов:
При прошивке принтера был сбой и отключения тока. На принтере был версия V1.01.00.81 прошивался на V1.01.00.84 петем замены сериал номера до этого прошил 5-6 таких принтеров все с этим прошивкой работает нормально. после сбоя принтер не прошивается отчет не печатает вот и отчет терминала через дебаг
(click to show/hide)[ POWER ON Booting... ]
Press any key to execute Monitor Program within 1 sec...
New kernel was found...
CHKSUM
{
check sum start address : 004F0000, count : 00101000
check sum : 0000A5A5
} /* Checksum End
Checksum OK!!
Find Compressed Kernel
Kernel UnZip Done!!
JUMP address = 0x40D80000
jump to 0x40D80000NEW MAC
Begin MAA_Test Approval
NEW MAC
gIsIPv4PacketAccepted : 00000001
gIsIPv6PacketAccepted : 00000001
[ POWER ON Booting... ]
Press any key to execute Monitor Program within 1 sec...
New kernel was found...
CHKSUM
{
check sum start address : 004F0000, count : 00101000
check sum : 0000A5A5
} /* Checksum End
Checksum OK!!
Find Compressed Kernel
Kernel UnZip Done!!
JUMP address = 0x40D80000
jump to 0x40D80000NEW MAC
Begin MAA_Test Approval
NEW MAC
gIsIPv4PacketAccepted : 00000001
gIsIPv6PacketAccepted : 00000001
[ POWER ON Booting... ]
Press any key to execute Monitor Program within 1 sec...
New kernel was found...
CHKSUM
{
check sum start address : 004F0000, count : 00101000
check sum : 0000A5A5
} /* Checksum End
Checksum OK!!
Find Compressed Kernel
Kernel UnZip Done!!
JUMP address = 0x40D80000
jump to 0x40D80000NEW MAC
Begin MAA_Test Approval
NEW MAC
gIsIPv4PacketAccepted : 00000001
gIsIPv6PacketAccepted : 00000001
[ POWER ON Booting... ]
Press any key to execute Monitor Program within 1 sec...
New kernel was found...
CHKSUM
{
check sum start address : 004F0000, count : 00101000
check sum : 0000A5A5
} /* Checksum End
Checksum OK!!
Find Compressed Kernel
Kernel UnZip Done!!
JUMP address = 0x40D80000
jump to 0x40D80000NEW MAC
Begin MAA_Test Approval
NEW MAC
gIsIPv4PacketAccepted : 00000001
gIsIPv6PacketAccepted : 00000001
[ POWER ON Booting... ]
Press any key to execute Monitor Program within 1 sec...
<CPU:360Mhz RAM:166Mhz SysClk:120Mhz DDR2>
----------------------------------------------------------------
START-UP MODE : Monitor Program
Boot into pROBE+ like stand-alone mode
[Type 'help' to see command info.]
Version : Ver.0.30 (SANDPIPER) 2010-08-15
----------------------------------------------------------------
Do you want to download from external port?[N] : n
pROBE+> fl
Upgrade Flash ROM Image
==> Now program restarted on the RAM to program flash ROM(0x40020000)
jump to 0x40020000
Flash Data Download Address : 0x42000000
===============================
Start flash_writer
===============================
verify_Image : 0x42000000
i_header->pul_start_addr : 0x00000000
i_header->ul_count : 0x00000000
model : 0x00000000
flash type : 0x00000000
image type : 0x00000000
temp_buf :
SIG : $IMG
Can not find sig
----------- Display Dcache Status ------------
Control register = 0x000510F8
Icahe : ON
Dcahe : OFF
MMU : OFF
Download Image from PC
{
Ready to download from Parallel/Usb/Serial (0x42000000)
-------------------------
Samsung OTG, 2006
Link ID : [4F54240A]
-------------------------
Drv "design ware core" USB download<HS><HS><EPB_RX 0x00000200>
Image includes PJL(0000001B) -> Waste 48 bytes
[[7340104 Bytes received]] - Complete Downloading
} /* Download End */
verify_Image : 0x42000000
i_header->pul_start_addr : 0x00000000
i_header->ul_count : 0x00700000
model : 0x0300002F
flash type : 0x00010001
image typeheck sum start address : 42000018, count : 00700000
check sum : 0000A5A5
} /* Checksum End
Source Checksum is valid
ul_rom_size[0x42700018]
Found new kernel(0x424F0018)!!!!
ZIP Dest : 0x40D80000
[[[FFFFFFFF]]], [[[000F69A3]]]
Downloaded Image is not Valid
Reset Target and Run Flash Writing Program Again
[ POWER ON Booting... ]
Press any key to execute Monitor Program within 1 sec...
<CPU:360Mhz RAM:166Mhz SysClk:120Mhz DDR2>
----------------------------------------------------------------
START-UP MODE : Monitor Program
Boot into pROBE+ like stand-alone mode
[Type 'help' to see command info.]
Version : Ver.0.30 (SANDPIPER) 2010-08-15
----------------------------------------------------------------
Do you want to download from external port?[N] : n
pROBE+> fl
Upgrade Flash ROM Image
==> Now program restarted on the RAM to program flash ROM(0x40020000)
jump to 0x40020000
Flash Data Download Address : 0x42000000
===============================
Start flash_writer
===============================
verify_Image : 0x42000000
i_header->pul_start_addr : 0x00000000
i_header->ul_count : 0x00000000
model : 0x00000000
flash type : 0x00000000
image type : 0x00000000
temp_buf :
SIG : $IMG
Can not find sig
----------- Display Dcache Status ------------
Control register = 0x000510F8
Icahe : ON
Dcahe : OFF
MMU : OFF
Download Image from PC
{
Ready to download from Parallel/Usb/Serial (0x42000000)
-------------------------
Samsung OTG, 2006
Link ID : [4F54240A]
-------------------------
Drv "design ware core" USB download<HS><HS><EPB_RX 0x00000200>
Image includes PJL(0000001B) -> Waste 48 bytes
[[7340104 Bytes received]] - Complete Downloading
} /* Download End */
verify_Image : 0x42000000
i_header->pul_start_addr : 0x00000000
i_header->ul_count : 0x00700000
model : 0x0300002F
flash type : 0x00010001
image type : 0x00000000
temp_buf : $IMG
SIG : $IMG
FlashCheckSum
{
check sum start address : 42000018, count : 00700000
check sum : 0000A5A5
} /* Checksum End
Source Checksum is valid
ul_rom_size[0x42700018]
Found new kernel(0x424F0018)!!!!
ZIP Dest : 0x40D80000
[[[FFFFFFFF]]], [[[000F69A8]]]
Downloaded Image is not Valid
Reset Target and Run Flash Writing Program Again
[ POWER ON Booting... ]
Press any key to execute Monitor Program within 1 sec...
New kernel was found...
CHKSUM
{
check sum start address : 004F0000, count : 00101000
check sum : 0000A5A5
} /* Checksum End
Checksum OK!!
Find Compressed Kernel
Kernel UnZip Done!!
JUMP address = 0x40D80000
jump to 0x40D80000NEW MAC
Begin MAA_Test Approval
NEW MAC
gIsIPv4PacketAccepted : 00000001
gIsIPv6PacketAccepted : 00000001
[ POWER ON Booting... ]
Press any key to execute Monitor Program within 1 sec...
<CPU:360Mhz RAM:166Mhz SysClk:120Mhz DDR2>
----------------------------------------------------------------
START-UP MODE : Monitor Program
Boot into pROBE+ like stand-alone mode
[Type 'help' to see command info.]
Version : Ver.0.30 (SANDPIPER) 2010-08-15
----------------------------------------------------------------
Do you want to download from external port?[N] : n
pROBE+> fl
Upgrade Flash ROM Image
==> Now program restarted on the RAM to program flash ROM(0x40020000)
jump to 0x40020000
Flash Data Download Address : 0x42000000
===============================
Start flash_writer
===============================
verify_Image : 0x42000000
i_header->pul_start_addr : 0x00000000
i_header->ul_count : 0x00000000
model : 0x00000000
flash type : 0x00000000
image type : 0x00000000
temp_buf :
SIG : $IMG
Can not find sig
----------- Display Dcache Status ------------
Control register = 0x000510F8
Icahe : ON
Dcahe : OFF
MMU : OFF
Download Image from PC
{
Ready to download from Parallel/Usb/Serial (0x42000000)
-------------------------
Samsung OTG, 2006
Link ID : [4F54240A]
-------------------------
Drv "design ware core" USB download<HS><HS><EPB_RX 0x00000100>
Image includes PJL(0000001B) -> Waste 48 bytes
[[7340104 Bytes received]] - Complete Downloading
} /* Download End */
verify_Image : 0x42000000
i_header->pul_start_addr : 0x00000000
i_header->ul_count : 0x00700000
model : 0x0300002F
flash type : 0x00010001
image type : 0x00000000
temp_buf : $IMG
SIG : $IMG
FlashCheckSum
{
check sum start address : 42000018, count : 00700000
check sum : 0000A5A5
} /* Checksum End
Source Checksum is valid
ul_rom_size[0x42700018]
Found new kernel(0x424F0018)!!!!
ZIP Dest : 0x40D80000
[[[FFFFFFFF]]], [[[000F69A3]]]
Downloaded Image is not Valid
Reset Target and Run Flash Writing Program Again
Дорогой друг! Можно Вас попросить лог дебага прятать под спойлер. Спасибо, дорогой друг!
Aleksey Mo-skin:
Алгоритм следующий:
1. Входим в дебаг и нажимаем CTRL+C
2. На вопрос отвечаем нажатием клавиши [Y]
3. Вводим адрес 40d80000 и нажимаем [Enter]
4. Перетаскиваем файл You are not allowed to view links.
Register or Login на usbprns2.exe
5. На вопрос отвечаем нажатием клавиши [N]
6. Вводим команду go 40d80000
Далее принтер должен включится в обычном режиме, и сразу, не выключая, прошиваем оригинальной прошивкой You are not allowed to view links.
Register or Login
Рустам Умаркулов:
Через гипер терминал не принимает
Aleksey Mo-skin:
Что не принимает, подробнее.
Рустам Умаркулов:
1. Входим в дебаг и нажимаем CTRL+C
как войти в дебаг и не принимает CTRL+C
Навигация
Перейти к полной версии