Общение > Ремонт оргтехники

Samsung ml-1670 загружается в принудительном режиме [РЕШЕНО]

<< < (2/2)

vitekk:
Отлично буду ждать! пока принтер до конца недели!

Aleksey Mo-skin:
1. Входим pROBE>
2. Нажимаем Ctrl+C

"Do you want to download from external port?[N] :"
Нажимаем Y

"Enter Start Address[0x40017000] : 0x"
Нажимаем Enter

3. Перетаскиваем файл Kernel_ML1670_V1.01.00.11.hd (You are not allowed to view links. Register or Login) на usbprns2.exe

Снова спросит:
"Do you want to download from external port?[N] :"
Нажимаем N

4. Вводим команду go 40017000 и нажимаем Enter

Принтер должен включиться в обычном режиме, но это еще не все

5. Не выключая принтер прошиваем оригинальной прошивкой 11 версии


Если не получится - лог терминала сюда.

vitekk:
Вот лог
(click to show/hide)[ POWER ON  Booting... ]

Press any key to execute Monitor Program within 1 sec...

<CPU:300Mhz RAM:100Mhz SysClk:100Mhz >

----------------------------------------------------------------
START-UP MODE : Monitor Program
  Boot into pROBE+ like stand-alone mode
  [Type 'help' to see command info.]
<<<0x00000000>>>
  Version : BLUEBIRD_VE SEC Ver.0.51 2011-01-17 [1]
----------------------------------------------------------------
Do you want to download from external port?[N] : n

pROBE+>

----------------------------------------------------------------
Do you want to download from external port?[N] : y
Enter Start Address[0x40017000] : 0x
Ready to download from Parallel/Usb/Serial (0x40017000)
-------------------------
Link ID   : [4F54281A]
-------------------------
USB download<HS><HS><EPB_RX 0x00000200>
Special Image is downloading(font, etc)...
-> Address is 0x40017000
[[935152 Bytes received]] - Complete Downloading

----------------------------------------------------------------
Do you want to download from external port?[N] : n

pROBE+> go 40017000
Executing the code at 0x40017000

Assert :: ????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????
[PJL] Alloc memory to download FW : 0x404F5EC0
Flash Data Download Address : 0x404F5EC0

===============================
    Start flash_writer
===============================
firmware source address        : 0x404F5EC0
firmware address to be written : 0x00000000
firmware size                  : 0x0007D000
Main Model ID is Correct(0x03000061)!!!
Sub Model ID is Correct(0x00010002)!!!
Found new kernel!!!! (0x4050AED8)
[[[1000011]]], [[[1000011]]]
THIS IS a VALID IMAGE.!!!!
Image Verification is OK!!!
##### FLASH WRITING #####
RamSrcAddr   : 0x404F5ED8
RomStartAddr : 0x00000000
Romsize      : 0x0007D000
RomEndAddr   : 0x0007D000

[0x00000000]0x00010000 Bytes programmed
[0x00010000]0x00010000 Bytes programmed
[0x00020000]0x00010000 Bytes programmed
[0x00030000]0x00010000 Bytes programmed
[0x00040000]0x00010000 Bytes programmed
[0x00050000]0x00010000 Bytes programmed
[0x00060000]0x00010000 Bytes programmed
[0x00070000]0x0000D000 Bytes programmed
FW Upgrade Sucess !!!
Machine will reboot
[ WATCH DOG RESET  Booting... ]

Skip Download
Press any key to execute Monitor Program within 1 sec...
Loading Kernel...
Kernel Reading ... Done!!
New kernel was found...
checksum is valid
Loading Emulation..
Run Kernel..
Assert :: ??принтер стартует но мне не нравиться текущий лог или это нормально
(click to show/hide)[ POWER ON  Booting... ]

Skip Download
Press any key to execute Monitor Program within 1 sec...
Loading Kernel...
Kernel Reading ... Done!!
New kernel was found...
checksum is valid
Loading Emulation..
Run Kernel..
Assert :: ??Все замечательно заработало единственное оригинал заливался около 40 минут!!
На крайний случай прошил еще раз оригиналом через команду fl
Алексею огромное спасибо!

Навигация

[0] Главная страница сообщений

[*] Предыдущая страница

Перейти к полной версии