Fix-free forum | Прошивки принтеров и МФУ
Общение => Прошивки => Тема начата: elpitonio от Ноябрь 04, 2014, 11:13:55 am
-
Принесли данный аппарат. Отчет не распечатывался, на плате стояла V04, но прошивка никак не хотела залазить, в принудительный режим аппарат не становится(до этого он шился, но человек не в курсе какую заливал). Решил залить оригинал V11 через дебаг и вот что мне выдает:
[ POWER ON Booting... ]
Skip Download
Press any key to execute Monitor Program within 1 sec...
Loading Kernel...
Kernel Reading ... Done!!
New kernel was found...
checksum is valid
Loading Emulation..
Run Kernel..
Assert ::
-
И при нажатой кнопке и без он это выдает! Попробую перепоять перемычку! Если я не ошибаюсь, то она ставится на R17!?
-
Вот что пишет сейчас
[ POWER ON Booting... ]
Skip Download
Press any key to execute Monitor Program within 1 sec...
<CPU:300Mhz RAM:100Mhz SysClk:100Mhz >
----------------------------------------------------------------
START-UP MODE : Monitor Program
Boot into pROBE+ like stand-alone mode
[Type 'help' to see command info.]
<<<0x00000000>>>
Version : BLUEBIRD_VE SEC Ver.0.51 2011-01-17 [1]
----------------------------------------------------------------
Do you want to download from external port?[N] : о
pROBE+> fl
Run Firmware Upgrade Mode...
Flash Data Download Address : 0x40400000
===============================
Start flash_writer
===============================
firmware source address : 0x40400018
firmware address to be written : 0x00000000
firmware size : 0x00000000
<<<0x00000000>>>
<<<0x00000000>>>
Can not find sig
Download Image from PC
{
Ready to download from Parallel/Usb/Serial (0x40400000)
-------------------------
Link ID : [4F54281A]
-------------------------
USB download<HS><HS><EPB_RX 0x00000200>
Image includes PJL(0000001B) -> Waste 80 bytes
[[512104 Bytes received]] - Complete Downloading
} /* Download End */
firmware source address : 0x40400018
firmware address to be written : 0x00000000
firmware size : 0x0007D000
<<<0x00000000>>>
<<<0x00000000>>>
checksum is valid
Found new kernel(0x40415018)!!!!
Kernel Reading ... Done!!
[1000011], [1000011]
This is a valid image.!!!!
[[[[[ Flash Writing : BANK[0] 0x00000000]]]]]
flash_start_addr : 0x00000000
flash_end_addr : 0x0007D000
flash_data_size : 0x0007D000
src_image_start_addr : 0x40400018
0x00004000 words - 0x00010000 bytes programmed(13 percent : 0x0006D000)
0x00004000 words - 0x00010000 bytes programmed(26 percent : 0x0005D000)
0x00004000 words - 0x00010000 bytes programmed(39 percent : 0x0004D000)
0x00004000 words - 0x00010000 bytes programmed(52 percent : 0x0003D000)
0x00004000 words - 0x00010000 bytes programmed(64 percent : 0x0002D000)
0x00004000 words - 0x00010000 bytes programmed(77 percent : 0x0001D000)
0x00004000 words - 0x00010000 bytes programmed(90 percent : 0x0000D000)
0x00003400 words - 0x0000D000 bytes programmed(100 percent : 0x00000000)
checksum is valid
=>check sum is valid
[ WATCH DOG RESET Booting... ]
Skip Download
Press any key to execute Monitor Program within 1 sec...
Loading Kernel...
Kernel Reading ... Done!!
New kernel was found...
checksum is valid
Loading Emulation..
Run Kernel..
Assert ::
-
А теперь сделай то, что надо было сделать с самого начала - посмотри на что жалуется статус-монитор.
11-й ориг успешно залился, судя по логу.
-
Замените на новый катридж с тонером!
Теперь можно шить, но он отчет не печатает! Я так понял его шить под серийник,а не под КРУМ!?
-
Под серийник.