SCX3400 можно ли понизить версию прошивки через дебаг?

[Aleksey Mo-skin]

Если вывод в терминал идет, а команды не принимает - надо паять перемычку.
Нужно фото платы в районе контактов на дебаг с обеих сторон платы.

[sergeydm]

по ссылке есть фото с двух сторон

[NoEndOutcry]

Да все так, приконектился, дает какой-то ответ, но ответ не похож на то что было в прошлые разы. Что нужно делать вот в таком случае?

Loading boot application...
[NG0x00008260]

 Boot : Egmont FNW(C3N) V0.14 09-29-2011
 <Winbond W25Q64>

Press any key to execute Monitor Program within 1 sec...
Kernel Data Read Start From Serial Flash
Kernel Data Read End
Compressed Kernel was found (0x02800000)...
Decompressing Kernel to RAM
src_addr = 0x0280000C, dest_addr = 0x00100000, ul_size = 0x007BFC00

 Decompress ....................................................................
................................................................................
................................................................................
................................................................................
...................................... Done
Kernel Start [0x00100000]

[WARNNING]Timer5 is not running? check it!!
Serial Init for polling msg. sysHwInit : 650
 hardWareInterFaceInit
[wifiEndDrvPlug] enter

[wifiEndDrvPlug] end

sysHwInit2 755

sysHwInit2 762
Host Name: bootHost
Target Name: vxTarg[et
User: target
wifiEndStart ] start

[wifiEnd] Link Up
[wifiEndStart ] end
Instantiating /ram as rawFs,  device = 0x1
Formatting /ram for DOSFS
Instantiating /ram as rawFs, device = 0x1
Formatting...Retrieved old volume params with %38 confidence:
Volume Parameters: FAT type: FAT32, sectors per cluster 0
  0 FAT copies, 0 clusters, 0 sectors per FAT
  Sectors reserved 0, hidden 0, FAT sectors 0
  Root dir entries 0, sysId (null)  , serial number 10000
  Label:"           " ...
Disk with 64 sectors of 512 bytes will be formatted with:
Volume Parameters: FAT type: FAT12, sectors per cluster 1
  2 FAT copies, 54 clusters, 1 sectors per FAT
  Sectors reserved 1, hidden 0, FAT sectors 2
  Root dir entries 112, sysId VXDOS12 , serial number 10000
  Label:"           " ...
OK.

 ExceptionCheckMessage
====================== Check Boot [0xffffffff]
//////////////////////////////////////////////////////////////
//      VxWorks Stack Remain for Kernel..
mem 0
i
p
q
mem 4
mem 5
mem 8
mem 9
//      VxWorks Stack Free = (008eafd0)
//RAM_LOW_ADRS  = 00100000
//sysPhysMemTop = 08000000
//sysMemTop     = 02780000
//////////////////////////////////////////////////////////////
 <<< Reelase Mode >>>
<<<LogMsg_PrintOff>>>
 FFDrv_CheckInstall 1
 pDCB->ulSPINo 0
 pDCB->ulSlaveDevChannel 0
 FFDrv_CheckInstall 1
 pDCB->ulSPINo 0
 pDCB->ulSlaveDevChannel 1
<<<LogMsg_PrintOff>>>
<<<LogMsg_EngPrintOff>>>
 Model Code : SCX3405FW
 Main Kernel F/W Version : V3.00.01.13
 Main Kernel F/W Date : MAY-18-2012
DRAM:>
<<<HAL_InitWDT>>> WatchDog Initialized !!!
 Check PowerOn Mode PBA Port ---- ( GPIO1Ctrl - 0xde73c006 GPIO1Dir - 0x968cfff9
 GPIO1In - 0xfe00d1c2 )
 Check PowerOn Mode PBA Port ---- ( GPIO2Ctrl - 0xfa44241f GPIO2Dir - 0x87fbfbe3
 GPIO2In - 0x9fffe003 )
 ################### Normal Mode Start##########################
PrnVPUDrv Driver is Installed successfully
PrnVPUDrv Driver:Create and Added Device to DM(Handle=19204764)ipd: kill ipdhcpc
 failed: not found
ipd: start ipdhcpc6 ok

======NICCON Init Finish!!=========


*********************************************************************
[ImTMAA_RegisterItems] Error... JBIG ENC/DEC Function Needed...
*********************************************************************MT1900 Task
 Mode is 1
alreay existed symbolalreay existed symbolalreay existed symbol

 USB Port ON
 FFDrv_CheckInstall 1
 pDCB->ulSPINo 0
 pDCB->ulSlaveDevChannel 1
Warning!!
Warning!!
[ConAdmin] Mem Alloc Size (204800),      Avail (54784) in /home2/gv3system/prave
en.n/EC-19MAY/Egmont/GV3_Source/Subsystem/ConSS/App/ConIDS/IDS_Main.c 229 line
i
p
qWLAN_BCM_P2P_Initialize 155

 ===>>>  CJI_IF_PSH_GCPSetBusyState

• [P2P] Reinitialized P2P configuration

> > wl0 Link type:Ethernet  HWaddr 02:15:99:d2:6a:0a  Queue:none
        inet6 unicast fe80::15:99ff:fed2:6a0a%wl0  prefixlen 64  tentative  auto
matic
        UP RUNNING SIMPLEX BROADCAST MULTICAST
        MTU:1500  metric:1  VR:0  ifindex:3
        RX packets:0 mcast:0 errors:0 dropped:0
        TX packets:0 mcast:0 errors:0
        collisions:0 unsupported proto:0
        RX bytes:0  TX bytes:0

[UPNP_IF_Refresh] 1
[UPNP_IF_Refresh] 2
[mt1900_restart] start
[UPNP_IF_Refresh] 3

======WSD Init Finish!!=========

[Aleksey Mo-skin]

Да все так, приконектился, дает какой-то ответ, но ответ не похож на то что было в прошлые разы. Что нужно делать вот в таком случае?

Нормальный ответ для этих моделей.
Делать все как обычно. fl и прошиваем оригинал.

[NoEndOutcry]

Пытаюсь прошить, пишет вот такую штуку и все тут. пробовал разные версии оригинала шить

fl
[PJL-FWUpgrade] Parser BufPtr [Count=464,Stream=($VERV3.00.01.17     NOV-21-2012
)]
[PJL-FWUpgrade] FW Image Typs[KERNELNOBOOT,0]
[PJL-FWUpgrade] Version[V3.00.01.17     NOV-21-2012], Mode[1000]
[PJL-FWUpgrade] FW Image Start Address(0x0) Size(8388608)
[PJL-FWUpgrade] Set Job Register Block !!

[PJL-FWUpgrade] Engine status ready to download f/w.. DSAI=(0x80FF0004)

[PJL-FWUpgrade] MemHndl[0x45], AllocAddr[0x77fffc0], AllocSize[0x80001c]
[PJL-FWUpgrade][Case 2]
[PJL-FWUpgrade] 8388636-8388636 : Good
[PJL-FWUpgrade:3437] slCount(392,512,FF)
[PJL-FWUpgrade:3458] Some Data IS
[PJL-FWUpgrade] Set Job Register Available !!

[PJL-FWUpgrade] Parser BufPtr [Count=464,Stream=($VERV3.00.01.17     NOV-21-2012
)]
[PJL-FWUpgrade] FW Image Typs[EMUL,2]
[PJL-FWUpgrade] Version[V3.00.01.17     NOV-21-2012], Mode[1000]
[PJL-FWUpgrade] FW Image Start Address(0x0) Size(1069056)
[PJL-FWUpgrade] Set Job Register Block !!

[PJL-FWUpgrade] Engine status ready to download f/w.. DSAI=(0x80FF0004)

[PJL-FWUpgrade] MemHndl[0x45], AllocAddr[0x76faf80], AllocSize[0x10501c]
[PJL-FWUpgrade][Case 2]
[PJL-FWUpgrade] 1069084-1069084 : Good
[PJL-FWUpgrade:3437] slCount(0,240,FF)
[PJL-FWUpgrade][Download Error] DM Read Time out(3449,0)
[PJL-FWUpgrade] Set Job Register Available !!

[PJL-FWUpgrade] 0: H:45, A:77fffc0, S:80001c, s:80001c
[PJL-FWUpgrade] 1: H:0, A:0, S:0, s:0
[PJL-FWUpgrade] 2: H:45, A:76faf80, S:10501c, s:10501c
[PJL-FWUpgrade] 3: H:0, A:0, S:0, s:0
[PJL-FWUpgrade] 4: H:0, A:0, S:0, s:0
[PJL-FWUpgrade] 5: H:0, A:0, S:0, s:0
[PJL-FWUpgrade] 6: H:0, A:0, S:0, s:0
[PJL-FWUpgrade] 7: H:0, A:0, S:0, s:0
[PJL-FWUpgrade] 8: H:0, A:0, S:0, s:0
[PJL-FWUpgrade] 9: H:0, A:0, S:0, s:0
[PJL-FWUpgrade] 10: H:0, A:0, S:0, s:0
[PJL-FWUpgrade] 11: H:0, A:0, S:0, s:0
[PJL-FWUpgrade] 12: H:0, A:0, S:0, s:0
[PJL-FWUpgrade] 13: H:0, A:0, S:0, s:0
[PJL-FWUpgrade] 14: H:0, A:0, S:0, s:0
[PJL-FWUpgrade] trash flag - 0 kernel bit - 0
[JQ_FirmwareUpgrade]    JQInfo[0x0x37c0dc0]
[JQ] FWUInfo[0x37c1094]
[JQ] ulSSFlag : 0x5
[JQ]DSAI_SYSTEM_DEVICE_STATUS (0x80ff0001)

[JQ_notifyFWUpgradeToEngine] PIFCBRDG_IF_24VOnRequest(0) -
        Set BB_UI_UPGRADEMODE to Display FWU Message
        FWU Message Displayed
 ulSSFlag : 0x5
 SSIndex : 0x1
[JQ] SystemFWUpgrade
[FW_IL_MEMORY] Firmware Upgrade ---- Address[0x77fffc0]
verify_Image : 0x077fffc0
pstImageHeader->pulStartAddr : 0x00000000
pstImageHeader->ulFWDataSize : 0x00800000
MainModelID: 0x05000063
SubModelID : 0x00160002
FlashSelect : 0x00000000
Reserved2  : 0x00000000
Input Signature : $KER
SIG : $KER
SIG : $CMS
SIG : $EMU
SIG : $ENG
[JQ] PRD Value Board(17), SubModelID(0x00160002)

DramFlashCheckSum
{
check sum start address : 77fffdc, count : 800000
check sum : a5a5
} /* Checksum End

Source Checksum is not valid
Downloaded Image is not Valid
Reset Target and Run Flash Writing Program Again
Image Error Reset Printer

[Aleksey Mo-skin]

Вы шьете в обычном режиме, и непонятно зачем fl пририсовали.
При включении надо удерживать клавишу N, чтобы войти в режим vxshell, и только после этого вводить команду fl!

[NoEndOutcry]

Я удерживаю и fl набираю и ентер жму. Может не получилась перемычка? Попробую еще раз пропаять.

[Aleksey Mo-skin]

Вот пример прошивки SCX-3400 через дебаг:

(click to show/hide)

Loading boot application...

[NG0x00000AF3]



 Boot : Egmont(C3N) V0.12 08-01-2011

 <Winbond W25Q64>


Press any key to execute Monitor Program within 1 sec...

GO MonitorEntry



----------------------------------------------------------------

  START-UP MODE : Monitor Program

  [Type 'help' to see command info.]

  Version : Egmont(C3N) V0.12 08-01-2011

----------------------------------------------------------------

Do you want to download from external port?[N] : n

No

vxshell> nn

invalid command format



vxshell> fl



Upgrade Flash ROM Image



===============================

    Start flash_writer         

===============================

 <Winbond W25Q64>

Verify Image             : 0x01900000

i_header->pul_start_addr : 0x00000000

i_header->ul_count       : 0x00000000

 Model      : 0x00000000

 Flash Type : 0x00000000

 Image Type : 0x00000000

temp_buf :

SIG : $IMG



Can not find signature





Download Image from PC

{

Ready to download from Parallel/Usb/Serial (0x01900000)

-------------------------

Samsung OTG, 2006

Link ID   : [4F54281A] = [4F542000]

-------------------------

....Done.<HS><HS>

Image includes PJL(0000001B) -> Waste 92 bytes

[[4194424 Bytes received]] - Complete Downloading



} /* Download End */



Verify Image             : 0x01900000

i_header->pul_start_addr : 0x00000000

i_header->ul_count       : 0x00400000

 Model      : 0x05000063

 Flash Type : 0x00130002

 Image Type : 0x00000000

temp_buf : $KER

SIG : $IMG



FlashCheckSum



check sum start address : 0190001C, count : 00400000

check sum : 0000A5A5

} /* Checksum End



Source Checksum is valid

Boot image!

Found new kernel(0x0194001C)!!!!

 Decompress .......................................................................... Done

 Decompress .......................................................................... Done

cur : 0x50331928, new : 0x50331928

This is a valid image.!!!!

 Encryption Kernel check  OK



[[[[[ Flash Writing : BASE : 0x00000000]]]]]

SPI No. from - to ( 0 - 0)

flash_start_addr : 0x00000000

flash_end_addr   : 0x00400000

flash_data_size  : 0x00400000

src_image_start_addr : 0x0190001C

 [SFLASH_Erase] 00000000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(2 percent : 0x003F0000)

 [SFLASH_Erase] 00010000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(4 percent : 0x003E0000)

 [SFLASH_Erase] 00020000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(5 percent : 0x003D0000)

 [SFLASH_Erase] 00030000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(7 percent : 0x003C0000)

 [SFLASH_Erase] 00040000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(8 percent : 0x003B0000)

 [SFLASH_Erase] 00050000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(10 percent : 0x003A0000)

 [SFLASH_Erase] 00060000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(11 percent : 0x00390000)

 [SFLASH_Erase] 00070000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(13 percent : 0x00380000)

 [SFLASH_Erase] 00080000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(15 percent : 0x00370000)

 [SFLASH_Erase] 00090000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(16 percent : 0x00360000)

 [SFLASH_Erase] 000A0000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(18 percent : 0x00350000)

 [SFLASH_Erase] 000B0000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(19 percent : 0x00340000)

 [SFLASH_Erase] 000C0000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(21 percent : 0x00330000)

 [SFLASH_Erase] 000D0000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(22 percent : 0x00320000)

 [SFLASH_Erase] 000E0000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(24 percent : 0x00310000)

 [SFLASH_Erase] 000F0000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(25 percent : 0x00300000)

 [SFLASH_Erase] 00100000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(27 percent : 0x002F0000)

 [SFLASH_Erase] 00110000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(29 percent : 0x002E0000)

 [SFLASH_Erase] 00120000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(30 percent : 0x002D0000)

 [SFLASH_Erase] 00130000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(32 percent : 0x002C0000)

 [SFLASH_Erase] 00140000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(33 percent : 0x002B0000)

 [SFLASH_Erase] 00150000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(35 percent : 0x002A0000)

 [SFLASH_Erase] 00160000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(36 percent : 0x00290000)

 [SFLASH_Erase] 00170000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(38 percent : 0x00280000)

 [SFLASH_Erase] 00180000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(40 percent : 0x00270000)

 [SFLASH_Erase] 00190000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(41 percent : 0x00260000)

 [SFLASH_Erase] 001A0000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(43 percent : 0x00250000)

 [SFLASH_Erase] 001B0000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(44 percent : 0x00240000)

 [SFLASH_Erase] 001C0000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(46 percent : 0x00230000)

 [SFLASH_Erase] 001D0000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(47 percent : 0x00220000)

 [SFLASH_Erase] 001E0000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(49 percent : 0x00210000)

 [SFLASH_Erase] 001F0000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(50 percent : 0x00200000)

 [SFLASH_Erase] 00200000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(52 percent : 0x001F0000)

 [SFLASH_Erase] 00210000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(54 percent : 0x001E0000)

 [SFLASH_Erase] 00220000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(55 percent : 0x001D0000)

 [SFLASH_Erase] 00230000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(57 percent : 0x001C0000)

 [SFLASH_Erase] 00240000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(58 percent : 0x001B0000)

 [SFLASH_Erase] 00250000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(60 percent : 0x001A0000)

 [SFLASH_Erase] 00260000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(61 percent : 0x00190000)

 [SFLASH_Erase] 00270000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(63 percent : 0x00180000)

 [SFLASH_Erase] 00280000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(65 percent : 0x00170000)

 [SFLASH_Erase] 00290000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(66 percent : 0x00160000)

 [SFLASH_Erase] 002A0000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(68 percent : 0x00150000)

 [SFLASH_Erase] 002B0000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(69 percent : 0x00140000)

 [SFLASH_Erase] 002C0000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(71 percent : 0x00130000)

 [SFLASH_Erase] 002D0000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(72 percent : 0x00120000)

 [SFLASH_Erase] 002E0000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(74 percent : 0x00110000)

 [SFLASH_Erase] 002F0000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(75 percent : 0x00100000)

 [SFLASH_Erase] 00300000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(77 percent : 0x000F0000)

 [SFLASH_Erase] 00310000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(79 percent : 0x000E0000)

 [SFLASH_Erase] 00320000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(80 percent : 0x000D0000)

 [SFLASH_Erase] 00330000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(82 percent : 0x000C0000)

 [SFLASH_Erase] 00340000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(83 percent : 0x000B0000)

 [SFLASH_Erase] 00350000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(85 percent : 0x000A0000)

 [SFLASH_Erase] 00360000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(86 percent : 0x00090000)

 [SFLASH_Erase] 00370000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(88 percent : 0x00080000)

 [SFLASH_Erase] 00380000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(90 percent : 0x00070000)

 [SFLASH_Erase] 00390000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(91 percent : 0x00060000)

 [SFLASH_Erase] 003A0000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(93 percent : 0x00050000)

 [SFLASH_Erase] 003B0000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(94 percent : 0x00040000)

 [SFLASH_Erase] 003C0000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(96 percent : 0x00030000)

 [SFLASH_Erase] 003D0000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(97 percent : 0x00020000)

 [SFLASH_Erase] 003E0000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(99 percent : 0x00010000)

 [SFLASH_Erase] 003F0000, 00010000, 00010000

0x00004000 words - 0x00010000 bytes programmed(100 percent : 0x00000000)



FlashCheckSum



check sum start address : 0190001C, count : 00400000

check sum : 0000A5A5

} /* Checksum End



=>check sum is valid


Reset Printer




 System will be reset in 1 sec....




Loading boot application...

[NG0x00000000]



 Boot : Egmont(C3N) V0.12 08-01-2011

 <Winbond W25Q64>


Press any key to execute Monitor Program within 1 sec...

Kernel Data Read Start From Serial Flash

Kernel Data Read End

Compressed Kernel was found (0x01500000)...

Decompressing Kernel to RAM

src_addr = 0x0150000C, dest_addr = 0x00100000, ul_size = 0x0028AC00



 Decompress .......................................................................... Done

Kernel Start [0x00100000]



 FW Upgrade JUMP : 00392D8C

 RootWriteMonitorProgram : 000101B8

Serial Init for polling msg. sysHwInit : 651

 hardWareInterFaceInit
sysHwInit2 753

sysHwInit2 760
Host Name: bootHost
Target Name: vxTarget
User: target


 ExceptionCheckMessage

====================== Check Boot [0x0]

//////////////////////////////////////////////////////////////

//   VxWorks Stack Remain for Kernel..

mem 0

i

p

q

mem 4

mem 5

mem 8

mem 9

//   VxWorks Stack Free = (0077dfc0)

//RAM_LOW_ADRS  = 00100000

//sysPhysMemTop = 04000000

//sysMemTop     = 01400000

//////////////////////////////////////////////////////////////

 <<< Reelase Mode >>>

<<<LogMsg_PrintOff>>>

 FFDrv_CheckInstall 1

 pDCB->ulSPINo 0

 pDCB->ulSlaveDevChannel 0

<<<LogMsg_PrintOff>>>

<<<LogMsg_EngPrintOff>>>

 Model Code : SCX3405

 Main Kernel F/W Version : V3.00.01.18

 Main Kernel F/W Date : DEC-21-2012

DRAM:>

<<<HAL_InitWDT>>> WatchDog Initialized !!!

 Check PowerOn Mode PBA Port ---- ( GPIO1Ctrl - 0xde73c006 GPIO1Dir - 0x868cfff9 GPIO1In - 0xee00ffc2 )

 Check PowerOn Mode PBA Port ---- ( GPIO2Ctrl - 0xfb446b7f GPIO2Dir - 0xe22400 GPIO2In - 0x1cffa000 )

 ################### Normal Mode Start##########################
PrnVPUDrv Driver is Installed successfully
PrnVPUDrv Driver:Create and Added Device to DM(Handle=5783824)

*********************************************************************

[ImTMAA_RegisterItems] Error... JBIG ENC/DEC Function Needed...

*********************************************************************



 USB Port ON

i

p

q

Warning!!
Warning!!
[ConAdmin] Mem Alloc Size (204800),    Avail (57344) in /home/single/csqa/csqa_gv3_egmont/GV3_System/GV3_Source/Subsystem/ConSS/App/ConIDS/IDS_Main.c 229 line

 dwc_set_USBTrdTim : Bus Clock [120000000], TrdTim[2]

 dwc_set_USBTrdTim : Bus Clock [120000000], TrdTim[2]

[NoEndOutcry]

А есть какая-нибудь распиновка тх и рх с другой стороны, со стороны перемычки? У меня оторвался тх с корнем, теперь вообще не понятно к чему подпаиваться.

[NoEndOutcry]

Разобрался. Шьется. Оригинал прошило. А есть для него фиксы в свободном доступе или только покупка?

[eg0r0v]

a 3405FW реально по дебагу понизить?

[Demosfen]

Подскажите пожалуйста возможно ли понизить прошивку с 18 на 12 командой "pm.l 12d44 e3a00001" на SCX-3400?

[vxd]

Доброго времени суток. Присоединяюсь к последнему посту.
Имею 3400 в.18.
припаял дебаг,

Do you want to download from external port?[N] : n
No
vxshell> pm.l 12d44 e3a00001
invalid command format

соответственно не могу влить в.12
подскажите куда копать? другая команда нужна...
в стол заказов? Дык, до субботы еще 3 дня....
спасибо.

(click to show/hide)

~
Loading boot application...
[NG0x00000000]

 Boot : Egmont(C3N) V0.12 08-01-2011
 <Giga Device GD25Q32>

Press any key to execute Monitor Program within 1 sec...
Kernel Data Read Start From Serial Flash
Kernel Data Read End
Compressed Kernel was found (0x01500000)...
Decompressing Kernel to RAM
src_addr = 0x0150000C, dest_addr = 0x00100000, ul_size = 0x0028AC00

 Decompress ....................................................................
...... Done
Kernel Start [0x00100000]

 FW Upgrade JUMP : 00392D8C
 RootWriteMonitorProgram : 000101B8
Serial Init for polling msg. sysHwInit : 651
 hardWareInterFaceInit
sysHwInit2 753

sysHwInit2 760
Host Name: bootHost
Target Name: vxTarget
User: target

 ExceptionCheckMessage
====================== Check Boot [0xffffffff]
//////////////////////////////////////////////////////////////
//      VxWorks Stack Remain for Kernel..
mem 0
i
p
q
mem 4
mem 5
mem 8
mem 9
//      VxWorks Stack Free = (0077dfc0)
//RAM_LOW_ADRS  = 00100000
//sysPhysMemTop = 04000000
//sysMemTop     = 01400000
//////////////////////////////////////////////////////////////
 <<< Reelase Mode >>>
<<<LogMsg_PrintOff>>>
 FFDrv_CheckInstall 1
 pDCB->ulSPINo 0
 pDCB->ulSlaveDevChannel 0
<<<LogMsg_PrintOff>>>
<<<LogMsg_EngPrintOff>>>
 Model Code : SCX3405
 Main Kernel F/W Version : V3.00.01.18
 Main Kernel F/W Date : DEC-21-2012
DRAM:>
<<<HAL_InitWDT>>> WatchDog Initialized !!!
 Check PowerOn Mode PBA Port ---- ( GPIO1Ctrl - 0xde73c006 GPIO1Dir - 0x868cfff9
 GPIO1In - 0xee00f982 )
 Check PowerOn Mode PBA Port ---- ( GPIO2Ctrl - 0xfb446b7f GPIO2Dir - 0xe22400 G
PIO2In - 0x1cffa000 )
 ################### Normal Mode Start##########################
PrnVPUDrv Driver is Installed successfully
PrnVPUDrv Driver:Create and Added Device to DM(Handle=5783824)
*********************************************************************
[ImTMAA_RegisterItems] Error... JBIG ENC/DEC Function Needed...
*********************************************************************

 USB Port ON
i
p
q
Warning!!
Warning!!
[ConAdmin] Mem Alloc Size (204800),      Avail (57344) in /home/single/csqa/csqa
_gv3_egmont/GV3_System/GV3_Source/Subsystem/ConSS/App/ConIDS/IDS_Main.c 229 line

 dwc_set_USBTrdTim : Bus Clock [120000000], TrdTim[2]
 dwc_set_USBTrdTim : Bus Clock [120000000], TrdTim[2]
Loading boot application...
[NG0x00000000]

 Boot : Egmont(C3N) V0.12 08-01-2011
 <Giga Device GD25Q32>

Press any key to execute Monitor Program within 1 sec...
GO MonitorEntry

----------------------------------------------------------------
  START-UP MODE : Monitor Program
  [Type 'help' to see command info.]
  Version : Egmont(C3N) V0.12 08-01-2011
----------------------------------------------------------------
Do you want to download from external port?[N] : n
No
vxshell> pm.l 12d44 e3a00001
invalid command format

vxshell> fl

Upgrade Flash ROM Image

===============================
    Start flash_writer
===============================
 <Giga Device GD25Q32>
Verify Image             : 0x01900000
i_header->pul_start_addr : 0x00000000
i_header->ul_count       : 0x00000000
 Model      : 0x00000000
 Flash Type : 0x00000000
 Image Type : 0x00000000
temp_buf :
SIG : $IMG

Can not find signature


Download Image from PC
{
Ready to download from Parallel/Usb/Serial (0x01900000)
-------------------------
Samsung OTG, 2006
Link ID   : [4F54281A] = [4F542000]
-------------------------
....Done.<HS><HS><HS><HS>
Image includes PJL(0000001B) -> Waste 92 bytes
[[4194424 Bytes received]] - Complete Downloading

} /* Download End */

Verify Image             : 0x01900000
i_header->pul_start_addr : 0x00000000
i_header->ul_count       : 0x00400000
 Model      : 0x05000063
 Flash Type : 0x00130002
 Image Type : 0x00000000
temp_buf : $KER
SIG : $IMG

FlashCheckSum

check sum start address : 0190001C, count : 00400000
check sum : 0000A5A5
} /* Checksum End

Source Checksum is valid
Boot image!
Found new kernel(0x0194001C)!!!!
 Decompress ....................................................................
... Done
 Decompress ....................................................................
...... Done
cur : 0x3000118, new : 0x3000108
 Encryption Kernel check Error
Downloaded Image is not Valid
Reset Target and Run Flash Writing Program Againя
Loading boot application...
[NG0x00000000]

 Boot : Egmont(C3N) V0.12 08-01-2011
 <Giga Device GD25Q32>

Press any key to execute Monitor Program within 1 sec...
GO MonitorEntry

----------------------------------------------------------------
  START-UP MODE : Monitor Program
  [Type 'help' to see command info.]
  Version : Egmont(C3N) V0.12 08-01-2011
----------------------------------------------------------------
Do you want to download from external port?[N] : n
No
vxshell> fl

Upgrade Flash ROM Image

===============================
    Start flash_writer
===============================
 <Giga Device GD25Q32>
Verify Image             : 0x01900000
i_header->pul_start_addr : 0x00000000
i_header->ul_count       : 0x00000000
 Model      : 0x00000000
 Flash Type : 0x00000000
 Image Type : 0x00000000
temp_buf :
SIG : $IMG

Can not find signature


Download Image from PC
{
Ready to download from Parallel/Usb/Serial (0x01900000)
-------------------------
Samsung OTG, 2006
Link ID   : [4F54281A] = [4F542000]
-------------------------
....Done.<HS><HS>
Image includes PJL(0000001B) -> Waste 92 bytes
[[4194424 Bytes received]] - Complete Downloading

} /* Download End */

Verify Image             : 0x01900000
i_header->pul_start_addr : 0x00000000
i_header->ul_count       : 0x00400000
 Model      : 0x05000063
 Flash Type : 0x00130002
 Image Type : 0x00000000
temp_buf : $KER
SIG : $IMG

FlashCheckSum

check sum start address : 0190001C, count : 00400000
check sum : 0000A5A5
} /* Checksum End

Source Checksum is valid
Boot image!
Found new kernel(0x0194001C)!!!!
 Decompress ....................................................................
... Done
 Decompress ....................................................................
...... Done
cur : 0x3000118, new : 0x3000112
 Encryption Kernel check Error
Downloaded Image is not Valid
Reset Target and Run Flash Writing Program Again

[Anton]

купи разовый код для генера и не жди субботы...быстро, дешево, удобно!

[apopovv]

Здравствуйте! Пришлите пожалуйста прошивку для принтера samsung SCX-3400 .
версия прошивки: v3.00.01.18 DEC-21-2012 (SCX3405) . Серийный номер : Z6ZVB8KD4F01KFH . CRUM-130408S9139.

You are not allowed to view links. Register or Login

Спасибо!

В этом разделе не раздают.