Доброго дня суток. Подскажите как быть. Принесли принтер смсунг 3200 07вер.(китайский с ироглифами) прошил принтер с изменением серийника прошилось все вроде только перестал отчет печатать. недолго думая подсоеденил дебаг и прошил только прошил 08 версией признаюсь был невнимателен. при попытке прошить обратно на 07вер тупит
сначала через пробе меняю серийник
Boot&Mon. CheckSum OK!
[SFLASH_InitFLASH][NG]
[ POWER ON Booting... ]
Press any key to execute Monitor Program within 1 sec...
<CPU:375Mhz RAM:166Mhz SysClk:125Mhz DDR2>
----------------------------------------------------------------
START-UP MODE : Monitor Program
Boot into pROBE+ like stand-alone mode
[Type 'help' to see command info.]
Version : Ver.1.18 (BlueMT) 2010-10-15
----------------------------------------------------------------
Do you want to download from external port?[N] : n
pROBE+> fl
Upgrade Flash ROM Image
[SFLASH_InitFLASH][NG]
FlashCheckSum
{
check sum start address : 40060000, count : 00014FFE
check sum : 0000A5A5
} /* Checksum End
==> Now program restarted on the RAM to program flash ROM(0x40060000)
jump to 0x40060000
Flash Data Download Address : 0x40100000
===============================
Start flash_writer
===============================
[SFLASH_InitFLASH][NG]
verify_Image : 0x40100000
i_header->pul_start_addr : 0x00000000
i_header->ul_count : 0x00000000
model : 0x00000000
flash type : 0x00000000
image type : 0x00000000
temp_buf :
SIG :
Can not find sig
----------- Display Dcache Status ------------
Control register = 0x000510F8
Icahe : ON
Dcahe : OFF
MMU : OFF
Download Image from PC
{
Ready to download from Parallel/Usb/Serial (0x40100000)
-------------------------
Samsung OTG, 2006
Link ID : [00000000]
-------------------------
Drv "design ware core" USB download<HS><HS><EPB_RX 0x0000003F>
[ERR]Can't find е
Image includes PJL(0000001B) -> Waste 48 bytes
[[63 Bytes received]] - Complete Downloading
} /* Download End */
verify_Image : 0x40100000
i_header->pul_start_addr : 0x0D0A1B25
i_header->ul_count : 0x2D313233
model : 0x34355800
flash type : 0x00000000
image type : 0x00000000
temp_buf : 575W
SIG : 575W
-12345X
Can not find sig
Downloaded Image is not Valid
Reset Target and Run Flash Writing Program Again
потом пытаюсь прошить фиксом 07 верс
pROBE+> fl
Upgrade Flash ROM Image
[SFLASH_InitFLASH][NG]
FlashCheckSum
{
check sum start address : 40060000, count : 00014FFE
check sum : 0000A5A5
} /* Checksum End
==> Now program restarted on the RAM to program flash ROM(0x40060000)
jump to 0x40060000
Flash Data Download Address : 0x40100000
===============================
Start flash_writer
===============================
[SFLASH_InitFLASH][NG]
verify_Image : 0x40100000
i_header->pul_start_addr : 0x00000000
i_header->ul_count : 0x00000000
model : 0x00000000
flash type : 0x00000000
image type : 0x00000000
temp_buf :
SIG :
Can not find sig
----------- Display Dcache Status ------------
Control register = 0x000510F8
Icahe : ON
Dcahe : OFF
MMU : OFF
Download Image from PC
{
Ready to download from Parallel/Usb/Serial (0x40100000)
-------------------------
Samsung OTG, 2006
Link ID : [00000000]
-------------------------
Drv "design ware core" USB download<HS><HS><EPB_RX 0x00000200>
Image includes PJL(0000001B) -> Waste 92 bytes
[[4194424 Bytes received]] - Complete Downloading
} /* Download End */
verify_Image : 0x40100000
i_header->pul_start_addr : 0x00000000
i_header->ul_count : 0x00400000
model : 0x05000041
flash type : 0x00020002
image type : 0x00000000
temp_buf : $KER
SIG : $KER
FlashCheckSum
{
check sum start address : 4010001C, count : 00400000
check sum : 0000A5A5
} /* Checksum End
Source Checksum is valid
Not found new kernel!!!!
Downloaded Image is not Valid
Reset Target and Run Flash Writing Program Again
что мне делать??? с анг не очень дружу.
